The Loop-IP6820 is a gigabit Ethernet self-healing ring network termination unit (NTU). An important protocol supported is G.8032 Ethernet Ring Protection on its WAN ports. For ring topologies the IP6820 supports auto-discovery to discover all units on the ring (a maximum of 128) as well as remote configuration for easy installation.
All end equipment can be in packet format via Ethernet ports or serial data via RS232/422/485 interfaces, which are converted into packets within the IP6820. The device has two WAN optical interfaces, two LAN optical interfaces, four electrical LAN interfaces, and one alarm relay interface. Manufacturing options include four additional electrical LAN interfaces, four or eight RS232/422/485 interfaces, and two sets of Dry Contact in/out interfaces.
With an embedded GbE L2 switch chip, the IP6820 also supports RSTP and MSTP for all Ethernet ports. It can be powered by single DC or dual DC power depending on field requirements. PoE (Power over Ethernet) and PoE+ are available as manufacturing options. Physical DIN rail mounting is also supported.
Applications for the IP6820 include automation, SCADA, surveillance, traffic control, transportation, and IP networking. Network topologies include ring protection, point-to-point, and point-to-multipoint. Easy installation and configuration make maintenance and expansion simple.
Mechanical, Electrical, Environmental
- Full frontal access (ETSI) unit complies with IP30 standard
- DIN Rail mounting
- Alarm relay and ACO (alarm cutoff) button
- Power: Single/dual DC modules with dual feed
- Input voltage monitoring, instant voltage monitoring, and temperature monitoring
- RoHS Compliant
- IEEE 1613, IEC61850-3 (for DC -48 Vdc only)
Interface Ports
- WAN port with OA&M functionality
- Dual SFP optical housing interfaces
- Tributary ports
- Up to Eight ports 10/100/1000 BaseT Ethernet
- Two SFP housing ports
- PoE and PoE+ options available in DC48 only for LAN ports 3-10 (RJ45)
- Up to 8 RS232/RS422/RS485 interface ports supporting full or half duplex mode
- Auto-negotiating or forced speed for speed and full/half duplex for tributary Ethernet ports
Other Features
- Jumbo frame: Up to 9600 bytes
- Synchronization
- NTP V4 client
- Synchronous Ethernet
- Dry contact interface
- Two alarm inputs and two relay outputs
- Supports point-to-point and point-to-multipoint applications
Ethernet Functionality
- G.8032 Ethernet Ring for WAN ports
- IEEE 802.1d STP, 802.1w RSTP, 802.1s MSTP
- IEEE 802.3x Flow Control, 802.1q port based VLAN and port isolation, 802.1p QoS
- IEEE 802.3ad Link Aggregation Control Protocol (LACP), also known as port trunking
- IEEE 802.1X Radius Client
- Auto-discovery, auto-diagnostic, and remote configuration for easy
- installation (up to 128 units)
- Master/Slave units setting via DIP switch
- Loop Ethernet Automatic Protection Switching (LEAPS)* for WAN ports
- IEEE 802.1ad VLAN Stacking (Q-in-Q)
- IGMP snooping v1 and v2
OAM Protocols
- IEEE 802.3ah OAM Ethernet in First Mile (EFM)
- Supports dying gasp functionality
- IEEE 802.1ag OAM
- Connectivity Fault Management (CFM)
- Y.1731 OAM (available on WAN ports only)
Management
- SSH v2, Telnet
- SNMP v1/v2/v3
- HTTP management
- Web-based management via Loop-iNET
- Remote configuration upload/download via TFTP
- Download firmware upgrades via TFTP
RoHS compliant units are identified by the letter G appearing at the end of ordering code.
| Part Number |
Description |
Notes |
|
|
|
