The EnableIT™ 395 95W – 56V Gigabit PoE Injector (Power over Ethernet) is single port IEEE 802.3af/at/bt compliant Midspan/Endspan solution that is a compact and easy to install with RJ-45 Ethernet cabling. This elegant unit is ideal for installing any WiFi Wireless Access Point, Security camera or other PoE powered equipment. It eliminates the need for external power supply and its associated AC/DC power cabling, providing a compact, affordable, safe and reliable power solution over your wiring or existing Ethernet infrastructure.
The 395 95W High powered Gigabit PoE Injector is very lightweight and compact for most all applications and use. These units are easy and rapid to install with plug and play RJ-45 Ethernet jacks to quickly insert your wiring and go. As a 802.3af/at/bt compliant device, the Injector uses 4 wires in a category rated wiring bundle. i.e. CAT5e run required for Gigabit Ethernet. It is compatible with mid-span and end-span PoE power methods for PoE Device detection.
The Enable-IT 395 95W – 56V Gigabit PoE Injector supports both 2-pair and 4-pair PoE output and is ideal for installing high powered IP PoE devices up to 3,500ft when used in conjunction with an Enable-IT PoE Extender.
As will all PoE voltage drops over distance. As a rule of thumb you will lose 6V per every 100′- 200′ of wiring, depending on the gauge. Lower power also means more amperage means more heat and perhaps issues with the 24 gauge wires in CAT5. You may need to use 18 gauge wiring for best distance results.
- Designed and Made in the USA in High Quality Handcrafted Lots
- Professional Business Grade Product, Solid reliability not Chinese Home Use
- Includes a Industry leading 4 year Manufacturer Warranty
- Maintains existing RJ-45 Ethernet Data (10/100/1000mbps).
- Built in Auto-Recovery, Over-Voltage and Short Circuit protection for your valuable PoE electronics. Output can be shorted permanently without damage.
- 95W – 56VDC IEEE 802.3AT/AF/BT Power Over Ethernet Midspan/Endspan Injector.
- 4KV lightning surge protection – 2KV (Differential Mode), 4KV (Common Mode)
- ESD protection – Direct discharge: 6KV, Air discharge: 10KV
- FCC Part 15 Class B & EN55022 Class B.
- Fully Compliant 25k detection, disconnect and voltage control IEEE 802.3AT
- Over Voltage/Current, Short Circuit Protection Outputs equipped with short circuit protection and overload protection as per 802.3at specification except max average current is 0.55A, Peak 0.6A per pair
- Maintains existing RJ-45 Ethernet Data (10/100/1000mbps).
- Network Equipment independence – Transparent to protocols, applications and MAC addresses.
- Ideal for powering up High Wattage PTZ POE Cameras like the Axis Q-Series with heaters/AC
- FCC Class B Part 15 and EN55022 (CISPR 22) Class B.
- Immunity ESD: EN61000-4-2 level.
- Immunity RS : EN61000-4-3 level.
- Immunity CS : EN61000-4-6 level.
This kit includes the following:
(1) EnableIT™ 395 95W – 56V Gigabit PoE Injector
(1) (90 – 264V AC) Country Specific power cord provided
(1) EnableIT™ 395 95W – 56V Gigabit PoE Injector Quickstart Guide
(1) 4yr Manufacturer Warranty
Power
AC Input (90 – 264VAC)
DC output 95W – 56V DC IEEE 802.3af/at/bt Power Over Ethernet Midspan/Endspan Injector.
Country Specific IEC 60320C13 Grounded power cord provided.
Built in Auto-Recovery, Over-Voltage and Short Circuit protection.
Output Ripple <5%
PoE Pin Assignment 1/2/7/8(-), 3/6/4/5(+) TIA568A
Data Rate
1000Mbps full-duplex Ethernet Data
Interface
Ethernet: (1) LAN RJ-45 10/100/1000 Base-TX autosensing shielded socket for LAN Input
(1) LAN RJ-45 10/100/1000 Base-TX autosensing shielded socket for PoE output.
Dimensions
Height 1.67″ (42.5mm) Depth 6.65″ (169mm) Width 3.8″ (96.5mm)
Environment
Operational Temperature: -14°F to 104°F (-10°to 40°C)
Humidity: 5% to 95%, non-condensing
Enclosure
Ruggedized black ABS plastic casing
ORDERING INFORMATION
| Model # |
Description |
Availability |
| 395 |
Enable-IT 395 95W - 56VDC Gigabit PoE+ Injector - 802.3af/at/bt detect |
General Availability |
|
|
