Overview
The CL1211/EUI is a member of the CL1200 product series. The CL1211/EUI is a single-port verison of the CL1212. Combining data flows from up to 2 network-enabled devices onto a single twisted pair or coax cable, the CopperLink Model CL1212 can deliver IP traffic up to 1.8 miles (3 km) away—well beyond the standard 328-foot (100-meter) Ethernet distance limitation.
With achievable line rates up to 168 Mbps, the CL1212 eliminates the bandwidth constraints commonly experienced with other copper-based transmission technologies. The Model 1212 is engineered to re-use existing infrastructure previously employed in such legacy applications as alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV. Many newer cabling standards are also supported, including Cat 5e, Cat 6 and Cat 7.
A built-in two-port Ethernet switch makes the CopperLink CL1212 ideal for delivering multiple IP information streams over a single cable. At a guardhouse or security kiosk for example, you could aggregate IP data from a laptop and a high-resolution IP video camera for simultaneous transmission over a single Ethernet connection.
A single-port version, the CopperLink Model CL1211 (available by special order) is ideal forapplications requiring the enhanced security of asingle Ethernet port.
Applications
Typical Application: Extending Ethernet over Cat 5+ or UTP
Features
- Ethernet Extension—Extend 10/100Base-TX Ethernet well beyond its 328-foot (100-meter) limitation over a single unshielded twisted pair (UTP) or Cat 5e/6/7 cable.
- Operates Over Twisted Pair—Realize fiber-optic speeds without the expense—and hassle—of installing new cables or line-of-site wireless circuits.
- Plug and Play—Set these units up straight out of the box. No configuration is required. Dual auto-sensing 10/100 Ethernet ports support full or half duplex operation.
- Multiple Line Rates Supported—Switch-selectable rate mode options optimize rate and reach for the noise environment, wire gauge/type and length.
- Transparent LAN Bridging—Bypass network configuration requirements by transparently passing all higher layer protocols—including 802.1Q VLAN frames (tagged and untagged).
- Made in the USA— This Patton equipment is designed by Patton engineers and built in our Gaithersburg, Maryland facility. Patton's American-made manufacturing process delivers high-quality networking solutions with reliability you can trust.
SPECIFICATIONS
CopperLink Line Interface |
- RJ-45 (pin 4 = ring; pin 5 = tip)
- Terminal block, 2 position
|
CopperLink Line Modulation |
DMT (Discrete Multi-Tone) |
Ethernet Interface (x2) |
8-position, shielded RJ-45. Auto-sensing 10/100Base-TX with half or full duplex operation.
Model 1211 has one 10/100Base-TX port. |
Protocol |
Transparent to high layer protocols: supports 802.1Q VLAN tagged or untagged frames.
Transparent to IP Video schemes: fully transparent to such compression schemes as MPEG-4, H.264, and MJPEG. |
Target SNR Modes |
6 dB and 9 dB |
Management |
8-position DIP switch |
Monitoring |
8 LEDs display Power, Link, Ethernet 1–4, Remote, and Local status. |
Power Supply |
External AC: 100–240 VAC |
Compliance |
FCC Part 15A, CE Mark, EMC Directive 89/336/EEC, Low-Voltage Directive 73/23/EEC |
Environment |
- Temperature: 0 to 50°C
- Humidity: 5 to 95%, non-condensing
- Extended Temperature: -40 to 85°C ( CL1212E or CL1211E)
- Extended Humidity: 5 to 85%, condensing (CL1212E/CC or CL1211E/CC)
|
Dimensions |
4.13 W x 1.5 H x 3.15 D in. (105 W x 38.1 H x 95.3 D mm) |
Weight |
0.4 lbs (181 g) |
MTBF |
77,000 hours |
ORDERING INFORMATION
# |
Model # |
Description |
Availability |
|
CL1211/EUI |
High Speed CopperLink Ethernet Extender; 1 x 10/100BaseTX; RJ45 Line, 100-240VAC |
General Availability |